Tobyfit¶
Introduction¶
The purpose of Tobyfit is to enable you to fit to Horace datasets taking into account the broadening of the data arising from the resolution of the instrument. Even if the excitations in your sample were infinitely long-lives you would have non-zero broadening in energy and wave vector arising from numerous contributions. The spread of energies arise from:
the non-zero width in the moderator pulse;
the non-zero pulse width from the Fermi or disk choppers;
the different flight-times for the neutrons due to different distances that neutrons travel depending on the point of emission from the moderator, point of scattering ion the sampel and point of absorption in the detector.
The spread of wavevector arises from: - spread of angle of the incident neutrons at the sample from the non-zero width of the moderator; - the non-zero size of the sample; - a spread of scattering angles into a given detector element because of the non-zero size of the detector element.
Resolution effects can be quite considerable. Not only do they result in an increase in the energy width of peaks (thereby giving an illusory shorter lifetime of the excitations), they can also shift the positions of peaks depending on, for example, the curvature of dispersion relation within the resolution function. This can result in incorrect values of exchange constants being extracted from the data is resolution is ignored.
Tobyfit uses the multifit fitting interface to enable you fit your data to a model for S(Q,w) together with background functions. By default the S(Q,w) model can be global to all of the datasets you pass to Tobyfit i.e. a single model that applies with the same parameter values to all datasets, with independent background functions for each of the datasets. Alternatively, you can specify that the S(Q,w) model is local i.e. the parameters vary independently for each dataset, but you can constrain parameters to be bound between the S(Q,w) models so that, for example, they all share common magnetic exchange constants but the intensities and intrinsic lifetimes can vary independently for each cut.
Tobyfit therefore appears to operate just like multifit_sqw, with the same set of capabilities of controlling parameter setting, binding etc that all other multifit variants have. The difference is that Tobyfit uses instrument information in the sqw objects to convolute the S(Q,w) model(s) with the instrument resolution function using a Monte Carlo multi-dimensional integration, and provides some additional methods to control how the convolution is carried out. Note that the background functions are *not* convoluted with the resolution function - the assumption is that they are simply empirical functions such as linear background models and so resolution function convolution makes little sense.
Performing resolution convolution¶
Setting the sample and instrument information¶
The first thing you need to do is provide the sample and instrument information to your datasets. You can do this by creating a sample object. There is an object class called IX_sample which does this; type doc IX_sample for more information. An example invocation is :
my_sample = IX_sample(true,[1,0,0],[0,1,0],'cuboid',[0.03,0.03,0.04])
Next you must create an instrument description. Horace provides functions for the ISIS chopper spectrometers that do this. For example, for the MAPS spectrometer you can use
instru = maps_instrument (ei, frequency, chopper_type)
where
- ei
incident energy (meV)
- frequency
frequency of the Fermi chopper
- chopper_type
character that indicates the chopper type (in the case of MAPS this is ‘A’ , ‘B’ or ‘S’ for the sloppy chopper)
The functions for the other spectrometers are merlin_instrument, mari_instrument, and let_instrument.
Now you need to associate this information with the cuts you wish to fit with Tobyfit. Tobyfit will only fit sqw objects, because the information of each individual detector-energy bin is needed to perform the resolution convolution. This information is removed when you create cuts of type d1d, d2d, etc. If you have already created the cuts then you do the following:
my_cuts = set_sample (my_cuts, my_sample)
my_cuts = set_instrument (my_cuts, instru)
Note that these functions will operate on arrays of sqw objects, so you do not need to write for loops.
Alternatively, you can attach the information to the sqw file from which you are going to make the cuts:
set_sample_horace (my_sqw_file, my_sample)
set_instrument_horace (my_sqw_file, instru)
The advantage of doing this is that every cut you take from the sqw file will also have the sample and instrument information.
Fitting data¶
Once you have set the sample and instrument you can start fitting your data. To start, you need to create a fitting object, which in the following example we’ll give the name tf:
tf = tobyfit (my_cuts)
Now you have created this object, the procedure is just the same as for the various other flavours of multifit, and specifically the form of the fitting functions is the same as multifit_sqw. You can follow the link to multifit for the general information about how to create a fit, and multifit_sqw for the form of the function that models S(Q,w). For complete documentation use the Matlab help by typing doc sqw/tobyfit and navigate the links to the various methods for setting functions, parameters, fixed/free parameters and bindings between parameters.
In addition to all of the methods for setting up and performing a fit, there are a few that are specific to Tobyfit (and which are documented in full in the Matlab documentation at doc sqw/tobyfit). The most important are outlined below. There is also the possibility to refine the crystal orientation and the moderator lineshape.
Controlling number of Monte Carlo points¶
tf = tobyfit (my_data)
\t:
tf = tf.set_mc_points (10)
and to enquire of the current values
tf.mc_points
The default is 10. This is a good starting value.
Controlling which contributions to include in the resolution function¶
There are a number of contributions to the resolution function. As an example:
tf = tobyfit (my_data)
\t:
tf = tf.set_mc_contributions ('nomoderator') \t% excludes the contribution from the moderator
To control the other contributions navigate the Matlab help doc sqw/tobyfit. To enquire of the current values:
tf.mc_contributions